QC Lubricants
CAGE CODE 9Y364
7360 Milnor St. Philadelphia, PA 19136
(215) 333-4187
Direct Line

Toll Free
With Extension (800) 887-2436
For Technical Assistance:
Dial Extension 203 for Stan Jakubowski
For Sales:
Dial Extension 211 for Lu Ann Quinn or 224 for Lindsay Romero
Email Lu Ann Quinn  ♦   Email Lindsay Romero


Home

We actively supply a comprehensive line of MIL-SPEC  and commercial lubricants.

 

Products
Mil-Specs
MSDS
PDS and Other Docs
Product Shelf Life

QC BLU DEF Diesel Exhaust Fluid

 

advanced

Unirex™ S 2
Grease

Product Description

Unirex™ S 2 is a lithium complex thickened high-temperature grease, based on a low volatility, synthetic polyol ester fluid, fortified with performance-enhancing additives. It is uniquely suited for high temperature applications, with an upper operating temperature recommendation of 200º C / 392°F based upon ASTM D3336 performance. Additionally this grease possesses good oxidation stability, and rust preventive characteristics.

Features and Potential Benefits

Unirex S 2 grease is specially developed for high temperature applications where mineral oil based greases may not provide adequate protection. The ester base fluid has a low volatility at the working temperatures involved, this can lead to long grease life when compared to a conventional mineral oil product. Unirex S 2 is suitable for high temperature operations where frequent relubrication is not practical.

Unirex S 2 offers the following performance features:
♦  Outstanding high-temperature performance with better lubricity and wear protection than conventional grease
♦  Low base stock volatility helping to provide long lubricant life and potentially extend re-lubrication intervals.
♦  An upper operating temperature of 200º C /392°F based upon ASTM D3336 High Temperature Life performance

Applications

Application notes: The ester base oil of Unirex S 2 is not compatible with many common elastomer seal materials. For example, it may cause a softening or swelling of NBR seals. It is recommended that the equipment manufacturer or your ExxonMobil representative be consulted regarding seal compatibility in a specific application.

Unirex S 2 is recommended by ExxonMobil for severe applications including:

♦  Conveyor bearings in kilns and ovens
♦  Steel mill ladle bearings
♦  Jet aircraft starter clutch assemblies
♦  Critical oven bearings in Fiberglas manufacture

Typical Properties

Property Unirex S 2
NLGI Grade 2
Thickener Type Li-complex
Color, visual Orange/Brown
Worked Penetration,, ASTM D 217, mm/10 280
Dropping Point ASTM D 2265, ºC 280
4-Ball Wear, scar diameter, ASTM D 2266, mm 0.60
Viscosity of Base Oil at 40 ºC, ASTM D 445, cSt 170
Oil Separation, ASTM D 1742, mass % 3
Lubrication life at 204 ºC, ASTM D 3336, hours 500
Corrosion Prevention, ASTM D 1743, Rating Pass
4-Ball Weld Load, ASTM D 2596, Kg 160

Health and Safety
Based on available information, this product is not expected to produce adverse effects on health when used for the intended application and the recommendations provided in the Material Safety Data Sheet (MSDS) are followed. MSDS's are available upon request through your sales contract office, or via the Internet. This product should not be used for purposes other than its intended use. If disposing of used product, take care to protect the environment.

All trademarks used herein are trademarks or registered trademarks of Exxon Mobil Corporation or one of its subsidiaries. 

Copyright © 2001-2014 Exxon Mobil Corporation. All rights reserved.

back to Exxonmobile main page